Advanced Production Operations For Oil & Gas ( 3 Days )

Durasi : 08.30 - 16.30 WIB

The rapidly increasing worldwide demand for natural gas as an energy source requires expertise in gas engineering technology. Incorporating a balance between theory and application, course emphasis is on training participants for immediate application of acquired techniques to field problems.

Production is defined as the operations involved in bringing well fluids to the surface and preparing the fluids for transport to a refinery via pipelines or trucks. The first step in production is to start the well fluids flowing to the surface (called “well completion”). Well servicing and workover consists of performing routine maintenance operations (such replacing worn or malfunctioning equipment) and performing more extensive repairs, respectively. Well servicing and workover are an intermittent step and necessary to maintain the flow of oil and gas. Next, the fluid must be separated into its components of oil, gas, and water; stored; and treated (for purification), measured, and tested before being transported to the refinery.

This training will provide the principle and yet some practical and theoretical aspect that can be applied on daily work faced by production engineers and supervisor in the oil industry.

OBJECTIVE

All aspects of completions are covered in sufficient detail to permit participants to review his/her current practices The fundamental concepts of production operations and their proper application in the field Production equipment such as wellhead, tubing and packers, well completions and workover as well as well test and problems, production logging and cementing will also covered Production logs and how and when to use them; evaluation techniques for cement bond logs and pulse echo tools

Learn how to plan and implement well completions, workovers, stimulation treatments, and routine production operations with an efficiency that increases profits
Learn about the role of rock mechanics in completions, stimulation, and workovers
Be able to give suggest or discover the procedures and techniques that increase production and cut operating costs
Be Able to identify and implement production improvement opportunities that can be carried out by either rig or non-rig well interventions
Implementation of appropriate technology, either from internal or external sources, in well design, whilst ensuring that the well value is maximized

OUTLINE

1. GEOLOGICAL CONSIDERATION

• Formation Rock
• Primary and Secondary Migrations
• Reservoir Traps

2. RESERVOIR FUNDAMENTALS THEORY

• The Nature of Rocks and Fluids
• Porosity and Permeability
• Productivity Index
• Volumetric Calculation
• Other Calculations and Decline Curves

3. FLUID FLOW

• Well Productivity
• Choke and Reservoir Fluids
• Inflow and Outflow

4. PRODUCTION OPERATIONS

• Well head and Well Head EquipmentMultiple Orifice
• Routine Operations
• Opening and Shut-in Well Procedure

5. WELL TESTING AND SATELLITE SYSTEM

• Test Separator Operations and Equipments
• Gas Systems Instruments
• Flare System and Depressurizing
• Pigging Techniques and ProceduresSampling and Analysis
• BS & W and API Gravity Measurement
• Protective Steam Tracing

6. SURFACE PRODUCTION OPERATIONS

• Process, Level, Temperature and Pressure Controls
• Oil treating , Heater treater and Dehydrator
• Separators, Stage Separators and Sizing
• Two-phase and Three-phase Separation Skimmer tank and Flotation unit

7. WELL PROBLEMS

• Low Production and Formation Damage
• Low Reservoir
• Plug-in Tubing or Perforations
• High Viscosity
• High Back Pressure
• Inadequate Artificial Lift
• Water Production and Mechanical Problem
• Protective Steam Tracing

8. PRODUCTION LOGS

9. WELL COMPLETIONS

10. PRIMARY CEMENTING AND SQUEEZE CEMENTING

11. FLUID COMPLETIONS

12. SAND CONTROL

• Gravel Pack, Resin and Fraspac

13. WORKOVERS

14. PARAFFIN AND ASPHALTENES

• hemical analysis
• Precipitation Mechanism
• The wax and Paraffin Problems

15. OIL EMULSIONS

• Emulsion Built-up and Emulsifying Agent
• Sampling and Analysis
• Emulsion Treating
• Heat and Chemical Treatment
• Electrostatic Coalescing

16. SCALE PROBLEMS

• Scale Composition, Prediction and Identification
• Mechanic and Chemical methods
• Scale Prevention and Inhibitors

17. CORROSION PREVENTIONS

• Basic Theory
• Detection and Measurement
• Prevention and Material Used
• Coating and Chemicals
• Cathodic Protections and inhibitors

Trainer : Spectracentre Trainer Team